- Frontpage >
- Tips and Inspiration >
- Potholes in the gravel driveway – how to repair and maintain a gravel road
Potholes in the gravel driveway – how to repair and maintain a gravel road
After a wet autumn and a long winter, many gravel roads and gravel driveways are full of potholes and puddles. The holes get bigger with every car that drives over them and every downpour – so the sooner you fill them, the less work it will be.
In this guide you can see why potholes form, which gravel to use and how to repair them so they do not come straight back.
Why do potholes form in a gravel road?
- Standing water. Water is the biggest culprit. When water stands in a small dip, the gravel softens and cars push it out to the sides.
- Traffic. Wheels turning, braking and accelerating in the same spot wear the gravel away – for example at the turn into the carport.
- Frost and thaw. Water in the gravel freezes and expands, and when it thaws the road is soft and vulnerable.
- No fall. If the road is flat or dips in the middle, rainwater cannot run off.
When is the best time to repair?
The best time is in spring or autumn, when the gravel is moist but not waterlogged. Moist gravel packs down best when you compact it. If it is completely dry, you can water it lightly.
Avoid repairing in frosty weather or just after a heavy downpour, when the holes are full of water and mud.
Which gravel should you use?
- Road Gravel 0–16 mm is a crushed material that packs well and stays put. It is the classic choice for filling potholes in gravel roads and driveways.
- Clay Road Gravel 0–8 mm contains clay that binds the material together. It is good for smaller holes and as a wearing course on paths and roads.
- Road base 0–32 mm is used to fill the bottom of deep holes, or where the base layer under the road has disappeared. Finish with road gravel on top.
To find out more about which materials suit a new driveway, read the guide Gravel for driveways – which gravel and stones are best?.
How to repair a pothole in a gravel road
- Remove water and mud from the hole, and take out loose stones and soft material until you reach a firm base.
- Make the edges vertical, and loosen the bottom and sides slightly with a mattock or spade so the new gravel binds with the old.
- Fill the gravel in layers of 5–10 cm, and compact each layer with a hand tamper or a plate compactor. Fill deep holes with road base first.
- Fill slightly above the road level. The gravel settles when it is compacted and driven on, so allow 10–20% extra.
- Compact at the end so the surface is level with the rest of the road and forms neither a bump nor a new dip.
If there are many holes close together, it is often better to rake the whole stretch level and lay a new wearing course instead of patching hole by hole.
Create a fall so the water runs off
Potholes come back if water is left standing. That is why the fall is the most important thing when maintaining a gravel road:
- Make the road slightly higher in the middle so water runs off to both sides – or give it a fall to one side. A couple of centimetres per metre is enough.
- Make sure the water has somewhere to go, such as a grass verge, a ditch or a bed along the road. Water must not be left standing at the edge of the road.
- Give the driveway a fall away from the house so rainwater does not run towards the plinth and carport.
Ongoing maintenance of the gravel road
- Fill small holes straight away, before they grow large.
- Rake or scrape the road level in spring and autumn, and pull the gravel from the edges back towards the middle.
- Remove grass and weeds from the centre strip and the edges so the water can run freely.
- Lay a new wearing course every few years when the gravel has worn thin. A wearing course of 3–5 cm is usually enough.
How much gravel do you need?
Example 1 – patching potholes: 10 holes of approx. 50 × 50 cm and 8 cm deep:
10 × 0.5 m × 0.5 m × 0.08 m = 0.2 m³. With 15% extra for compaction, you need about 230 litres of road gravel.
Example 2 – new wearing course: A driveway of 3 × 15 metres (45 m²) with a 4 cm wearing course:
45 m² × 0.04 m = 1.8 m³. With 15% extra, you need about 2.1 m³.
Use our quantity calculator, or read more in the guide How much gravel, sand and soil do I need?. We deliver the gravel in bulk bags straight to your address.